(888) ipd-converters (888) 473-2668 www.ipdconverters.com c-44 50 55 60 65 70 75 80 85 90 95 12345678910 x10 = load % efficiency % hes033ze hes075zg hes100ze technical specifications hes single output dc/dc converters provide up to 150 watts of output power in an industry standard, half-brick package and footprint. these units feature ultra-high efficiency, class a conducted noise specs, and fixed switching frequency. the hes is designed with open-frame packaging, along with planar magnetics to provide maximum useable power with minimal thermal constraints. the hes is especially suited to harsh telecom, networking, and industrial applications, and is fully compatible with production board washing processes. ? high efficiency industry standard half- brick open-frame packaging 100c baseplate operation water washable ?true-trim? option 1500v isolation positive or negative logic description features hes series - 150 watt general turn-on time 10 ms remote shutdown positive or negative logic remote shutdown reference v in negative switching frequency 2.5 & 3.3, 5v model 200 khz, 300 khz (respectively) isolation input - output 1500 vdc input - case 1050 vdc output - case 500 vdc temperature coefficient 0.2%/c case temperature operating range -40 to +100c storage range -40 to +125c thermal shutdown range 105 to 1 15c vibration, 3 axes, 5 min each 5 g, 10 - 55 hz mtbf ? (bellcore tr-nwt-000332) 1.8 x 10 6 hrs safety ul 1950, csa 22.2-950, en60950 weight (approx.) 1.4 oz notes 1 industrial temp range of -40 to +85c available, add suffix -i to p/n ? mtbf predictions may vary slightly from model to model. specifications typically at 25c, normal line, and full load, unless otherwise stated. soldering conditions: i/o pins, 260c, ten seconds; fully compatible with commercial wave-soldering equipment. safety: agency approvals may vary from model to model. please consult factory for specific model information. units are water-washable and fully compatible with commercial spray or immersion post wave-solder washing equipment. efficiency vs. load (48v input) output setpoint accuracy 1% line regulation v in min. - v in max., i out rated 0.2% v out load regulation i out min. - iout max., v in nom. 0.2% v out remote sense headroom 0.5 vdc minimum output current 10 % dynamic regulation, loadstep 25% i out pk deviation 4% v out settling time 500 s voltage trim range 10% short circuit / overcurrent protection shutdown / hiccup current limit threshold range, % of i out rated 110 - 130% ovp trip range 120 - 140% v out nom. ovp type self recovering voltage range 24 vdc nominal 18 - 36 vdc 48 vdc nominal 36 - 72 vdc reflected ripple 50 ma input reverse voltage protection shunt diode input undervoltage lockout / hysteresis <34v /1v nom. input
c-45 vin (volts) vin range (volts) iin max.* (amps) vout (volts) iout rated (amps) ripple & noise pk-pk (mv) efficiency typ. ** model 48 48 48 48 48 48 48 48 48 48 48 48 48 36 - 72 36 - 72 36 - 72 36 - 72 36 - 72 36 - 72 36 - 72 36 - 72 36 - 72 36 - 72 36 - 72 36 - 72 36 - 72 0.89 1.13 1.62 1.33 1.69 2.42 1.77 2.26 3.23 2.60 3.33 4.72 2.20 2.5 3.3 5 2.5 3.3 5 2.5 3.3 5 2.5 3.3 5 2.1 10 10 10 15 15 15 20 20 20 30 30 30 30 100 100 100 100 100 100 100 100 100 100 100 100 100 89% 87% 88% 86% 88% 89% 86% 85% 88% 82% 83% 86% 80% hes025zd-a hes033ze-a hes050zg-a hes037zd-a hes050ze-a hes075zg-a hes050zd-a hes066ze-a hes100zg-a hes075zd-a hes100ze-a hes150zg-a hes063zc-a * maximum input current at minimum input voltage, maximum rated output power. ** at nominal vin, rated output. mechanical drawing thermal impedance natural convection 15.4 c/w 100 lfm 12.2 c/w 200 lfm 9.3 c/w 300 lfm 7.4 c/w 400 lfm 6.4 c/w tolerances note: thermal impedance data is dependent on many environmental factors. the exact thermal performance should be validated for specific application. hes series - 150 watt 1 +v in 2 -v in 3 no pin (shutdown) 4 +v out 5 no pin (trim) 6 -v out inches: (millimeters) .xx 0.020 .x 0.5 .xxx 0.010 .xx 0.25 pin: 0.002 0.05 ( dimensions as listed unless otherwise specified.) pin function models - (see the last page of this file for options.) mounting inserts m3x.5 through 4pl 1.400"(35.6mm) 1.000"(25.4mm) 0.700"(17.8mm) 0.400"(10.2mm) 0 -0.50"(-12.7mm) 2.40" (61.0mm) 2.28" (57.9mm) bottom view 1 2 3 4 5 6 7 8 9 0.18" dia 0.080" dia 0.040" 0.025" ref. 0.50" (12.7mm) (4.6mm) (1.0mm) (2.0mm) (0.6mm) 0 1.900" (48.3mm) -0.19" (-4.8mm) 2pl 7pl
c105 options when ordering equipment options, use the following suffix information. select the option(s) that you prefer and add them to the model number. example ordering options are located below the options table. option suffix applicable series remarks negative logic n has, hbd, hbs, hes, les, qbs, qes, tes, tqd ttl ?low? turns module on ttl ?high? turns module off lucent compatible trim t has, hbd, hbs, hes, qbs, qes t e r m i nal s t r i p t s x w s , xwd, xwt trim 1 ias, les enable 2 iad, ias, les, sms trim and enable 3 ias, les current share 4 sms headerless y encapsulated ews, iws, ows pin length and heatsink options standard pin length is 0.180? (4.6mm) 0.110? (2.8mm) pin length 8 all units (except sms) 0.150? (3.8mm) pin length 9 all units (except sms) 0.24? (6.1mm) horizontal heatsink 1h all units (except dip, sip, and sm packages) includes thermal pad 0.24? (6.1mm) vertical heatsink 1v all units (except dip, sip, and sm packages) includes thermal pad 0.45? (11.4mm) horizontal heatsink 2h all units (except dip, sip, and sm packages) includes thermal pad 0.45? (11.4mm) vertical heatsink 2v all units (except dip, sip, and sm packages) includes thermal pad 0.95? (24.1mm) horizontal heatsink 3h all units (except dip, sip, and sm packages) includes thermal pad 0.95? (24.1mm) vertical heatsink 3v all units (except dip, sip, and sm packages) includes thermal pad example options:hbs050zg-ant3v = hbs050zg-a with negative logic, lucent compatible trim, and 0.95? vertical heatsink. les015yj-3n = les015yj with optional trim and enable, negative logic. qbs066zg-at8 = qbs066zg-a with lucent compatible trim and 0.110? pin length. nuclear and medical applications power-one products are not authorized for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the president of power-one, inc. technical revisions the appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. specifications are subject to change without notice.
|
